Skip to content
RoofElm

Roof

Gutters and drainage: moving roof water away from the house

What a gutter job includes, how much water a roof sends down, and where the downspouts should end up.

By RoofElm Editorial Team Updated 7 min read

Area that sheds water
Roof footprint, not slope
Water per inch of rain
About 0.6 gal per sq ft
Gutter run per downspout
50 ft max (CDA guide)
Permit
Ask your building office
Illustration: a roof edge with a gutter, hangers, a downspout and an extension carrying water away from the wall
A gutter system: trough, hangers, outlet, downspout and a discharge point away from the wall.

In short

A roof sends a lot of water to the edge in a short time, and the job of gutters and downspouts is to carry all of it past the foundation. Size the system from the roof's footprint, not its sloped surface: 1,200 square feet of footprint puts about 720 gallons through the gutters in one inch of rain, using a rounded constant. The gutters are only half the job. If the downspouts empty beside the wall, the water comes back to the foundation. Use this page to understand the parts, the sizing math and the questions to ask. If a roof replacement is coming, read roof replacement first, since gutters are easiest to redo at the same time.

What a gutter job includes

A gutter job is more than the trough. The fascia board behind it has to be solid, because the hangers hold the gutter's weight plus water, ice and leaves. A roofer or gutter installer can also tell you whether the drip edge, the metal strip at the roof edge, sends water into the gutter and not behind it.

  • Gutters: the trough along the eave, pitched toward a downspout.
  • Hangers or brackets: they fasten the trough to the fascia or the rafter ends.
  • Outlets and downspouts: the openings and pipes that carry water down.
  • Corners, end caps and joints: where most leaks start, so ask how they are sealed.
  • Extensions or splash blocks: they carry water out beyond the wall at the bottom.
  • Fascia and drip edge repair: if the wood behind the old gutter is rotted, it has to be fixed first.

Gutter guards and screens are an option, not a requirement. Ask what the guard is made of, how you clean it and whether it fits the gutter you are buying. Do not accept a claim that a guard means you never clean gutters again.

Sizing from the footprint

Rain falls straight down, so what counts is the area of ground the roof covers, called the footprint, and not the sloped surface that roofers measure in squares. Oklahoma State University Extension says to calculate a roof's catchment area from the footprint and not from the roof surface. A sloped surface is always larger than the ground under it, so use the footprint for water and the surface for shingles.

The conversion is simple. One inch of rain on one square foot is 144 cubic inches of water, and a U.S. gallon is 231 cubic inches, so each square foot gives about 0.623 gallons per inch. Oklahoma State's rainwater guide rounds this to 0.6. Here is a worked example for a footprint of 1,200 square feet.

Example: runoff from a 1,200 square foot roof footprint in one inch of rain
StepMathResult
Rounded constant (0.6)1,200 × 0.6720 gallons
Exact conversion1,200 × 144 ÷ 231about 748 gallons
Split over 4 downspouts720 ÷ 4180 gallons each
Two inches of rain720 × 21,440 gallons

Those totals say how much water has to be moved, but not how fast. What decides whether a gutter overflows is the rate, in inches per hour, in your worst local storms, so ask the installer what rainfall rate they sized for. A larger gutter, more downspouts or both are the usual answer for a big roof or a heavy-rain climate.

Downspouts and where the water goes

More downspouts mean less water in each one and less load on each gutter run. The Copper Development Association's design guide for hung copper gutters says each downspout should drain a maximum of 50 feet of gutter, and that expansion joints can limit that further because water cannot flow past one. That guide is written for copper, but the logic of short runs holds for any gutter. Avoid downspouts that must turn a corner to reach the outlet.

At the bottom, the water has to leave the wall. A downspout that dumps beside the foundation soaks the soil there. Use an extension or a splash block, and check that the ground slopes away from the house. The model building code sets a minimum slope for the ground near a foundation, and your building office can tell you the local version. Where the downspout empties also matters to neighbors and sometimes to the city, so do not aim it at a sidewalk, a neighbor's yard or a sewer line without checking local rules.

What drives the price

Gutter bids vary because of what is being built. We give no price ranges, since they age fast. Compare the factors below, and ask each installer for a price per linear foot with the same scope.

Length and height

A long eave and a two-story wall mean more material, more ladder time and more safety setup.

Material and size

Aluminum, steel, copper and vinyl differ in cost and durability. Larger troughs cost more.

Condition behind the gutter

Rotted fascia or a damaged drip edge must be fixed first, which adds to the bid.

Downspout count and discharge

More downspouts, buried drain lines and long extensions add cost, and they decide where the water ends up.

Questions to ask before you sign

  1. Ask how the installer sized the gutters and downspouts, and what rainfall rate was used.
  2. Ask how many downspouts there will be, where each one is, and where each one discharges.
  3. Ask what happens to the old gutters, and who repairs any rotted fascia and for what price per foot.
  4. Get the material, the gutter size, the color and the hanger type in the bid, and ask for the written warranty on both the material and the labor.
  5. Compare bids line by line with the estimate reading guide.
  6. Ask for a certificate of insurance sent by the insurer. Hiring a contractor explains how to check.

Permit rules for gutters differ by place, and a historic district, a homeowner association or a city drainage rule may apply. A quick call to the building office settles it.

DIY or hire out

Single-story gutter work is a DIY job for many handy people: clearing leaves, resealing a joint, adding an extension, or hanging a short run. Keep the ladder on firm, level ground, do not lean out from it, and stay far from power lines at the service drop. Two-story work, long runs and anything above a porch roof are for a pro with the right ladders and fall protection.

A good DIY habit is checking the system during a heavy rain. Watch for overflow at corners, water behind the gutter and puddles at the base of the downspouts. Write down what you see in your records, and bring the list to the installer. If the water problem reaches the yard, grading and landscaping may be the real fix, and landscaping covers that side. For the order in which to fix things, see what to fix first.

Common questions

How many gallons of water does my roof shed in a rain?

Multiply the roof footprint in square feet by the inches of rain and by about 0.62. A footprint of 1,200 square feet in one inch of rain gives roughly 748 gallons, or 720 with the rounded constant 0.6 that Oklahoma State University Extension uses.

Do I measure the roof surface or the footprint for gutter sizing?

The footprint. Rain falls straight down, and Oklahoma State University Extension says to calculate catchment area from the footprint. The sloped surface is what you use for shingles, not for water.

How many downspouts do I need?

It depends on roof area, rainfall rate and gutter size. One design guide for copper gutters caps each downspout at 50 feet of gutter, so a long eave needs more than one. Ask the installer to show the count and how it was sized.

Do I need a permit to replace gutters?

It depends on where you live. Historic districts, homeowner associations and local drainage rules can apply, so call your building office before you order.

Sources

Facts checked on November 19, 2026. The 144 cubic inches per square foot and 231 cubic inches per gallon behind the 0.623 figure are standard unit conversions. Sizing depends on local rainfall: confirm with the installer and your building office.